- Category: Tech Tips
With so many cast polyurethane systems available in the marketplace today, selecting the best material for a new prototype or part can be a most challenging process. Innovative Polymers’ experienced technical service team specializes in helping customers evaluate and choose materials. To provide effective input, however, we must have specific project information including:
- Part performance properties
- Processing and handling criteria
- Special requirements
It is by working in partnership with customers that we can most accurately answer the often asked question, “Which material will meet my needs?”
The first step is evaluating the part to be molded.
The mechanical stresses, required dimensional tolerances, surface finish, and service environment/temperatures in which the part will be used are keys to polyurethane selection.
Our technical representatives frequently receive difficult to answer questions...
Question 1. "I’m looking at a part specification that requires a tensile modulus of 250,000 psi. What do you have?"
Why is this hard to answer? Because every polyurethane is formulated with a series of physical characteristics. When a single characteristic is deemed "most important", as is tensile modulus in our example, this should be regarded as the starting point. Then, additional characteristics can be considered to select a material that best fits the application. Innovative Polymers suggests that customers do as much research as possible to determine all physical part parameters before calling our hot-line (1-800-340-4563).
Question 2. “Do you have a polyurethane that replicates ABS?”
Unlike the previous query that was too narrow in scope, this question is a bit too broad. It is important to understand that cast polyurethane systems (thermosets) cannot attain all of the physical properties of injection molded thermoplastics. While thermoset polyurethanes can provide similar performance and can meet individual property needs, the full combination of properties available in an ABS material cannot be attained in a polyurethane system. If a customer calls asking for ABS, we typically ask which specific property is most important. For example, if the part must be ultra-durable and able to withstand impact, our Tech Team would probably recommend a polyurethane that offers high impact resistance. However, this same material might not meet the flexural modulus indicated on the engineering specification.
Also, customers must keep in mind that all thermoplastics (ABS, polyethylene, polypropylene, etc.) have many grades. While one ABS plastic may have a very high flex modulus of 800,000 psi (very stiff), another may have a flex modulus of 275,000 psi (relatively stiff). Again, direct information about performance requirements for the cast part is critical before we can make a recommendation.
Question 3. Can you color the polyurethane I selected a specific color?
It is important to provide the Technical Representative with details about color requirements at the beginning of the conversation. Some materials are, for example, naturally dark in color and cannot, therefore, be pigmented to attain light color shades. If a comprehensive discussion has already taken place and a specific material selected before color is considered, the whole recommendation process will have to start again from the beginning. For more information about polyurethane color options, click here: http://www.innovative-polymers.com/tech-tips/81-coloring- innovative-polymers-products).
Question 4. I don’t have many details on required part performance but I do know it will be used outdoors. What do you recommend?
In the absence of information about required physical properties, it is at least important to evaluate anticipated service conditions. For example, if a fixture is being molded for an outdoor planter, the selected polyurethane must be able to withstand exposure to temperature extremes, humidity and rain, and the destructive effects of ultra-violet rays from the sun. Innovative Polymers InnoClearTM water clear polyurethanes are UV-resistant and may be the answer to this type of application.
Question 5. Are you willing to develop a system to meet our specifications?
Our chemists custom formulate polyurethanes at no additional cost to the customer to ensure that the material we supply is a “best fit” for the application. Using the right thermoset system from the beginning of a program can mean the difference between success and serious losses! When a new material is required, however, adequate time must be allowed for needed formulating work.
Among the factors to consider in selecting the best polyurethane for a project is its work life. The gel time of the material must be long enough to provide for complete mold filling before components begin to cure. Remember that shop temperature affects work life; higher than 77oF temperatures will decrease gel time while lower than 77oF can increase gel time and affect the cure cycle.
Molding process is also important. If a part will be vacuum cast, for example, a polyurethane like those in the Innovative Polymers RapidVacTM line should be selected. These products feature low viscosities with rapid gel times and perform well with the equipment used in vacuum casting. Specific parts may require degassing or pressure casting. Or, if being processed via meter/mix equipment, the polyurethane may be subjected to higher pressures and temperatures than when being hand cast in a silicone rubber mold.
Some projects may require a special handling. A common example is new designs/parts that are covered by secrecy restrictions. Innovative Polymers is very willing to sign a non-disclosure agreement to keep all discussions confidential. We are also happy to participate in conference calls with the end customer to review particularly complex projects and critical materials properties to help select the right polyurethane.
We look forward to working with you on your next project! Customer satisfaction is our number one priority!
RAMPF acquires US company Innovative Polymers, Inc.
Grafenberg, July 1, 2016. RAMPF has acquired the US COMPANY INNOVATIVE POLYMERS, INC., a provider of technologically advanced polyurethanes for tooling and modelling applications. With this acquisition, RAMPF is set to further expand its range of products in the NAFTA markets.
Innovative Polymers, Inc. will be integrated into RAMPF’s North American subsidiary RAMPF GROUP, INC., which offers RAKU-PUR® modeling and styling boards, Close Contour castings, blocks and pastes, as well as liquid systems on the NAFTA markets since 2003. » Continue reading
Innovative Offers Two New Tools to Improve Your Project’s Success
Innovative has developed two new ways to access instant help when using our materials to create your polyurethane projects. One is a Processing Guide which includes many tips that will help you avoid making common mistakes and the other is an introductory step-by-step casting video. We believe you will find a great benefit in viewing both resources before attempting your next project.
Innovative Polymers Upgrades Family of High-performance Polyurethanes
The InnoTuf® HP-2100 family of ultra-durable, room-temperature processable polyurethanes has been expanded to better serve customer and industry requirements. As with all Innovative Polymers' products, InnoTuf® formulations are mercury-free and contain neither MOCA nor free-TDI. » Read more
Rock Candy Chooses Polyurethane For Climbing Holds
With more than 7.8 million participants* in the U.S., recreational climbing on artificial indoor walls, in recent years, has surpassed outdoor climbing and become a recognized sport with nationwide and international competitions, publications and even a “lingo” unique to wall climbing enthusiasts. To support enthusiasts’ ever-growing demand for varied climbing experiences, manufacturers are producing walls with larger and more challenging surfaces, routes and holds.. » Read more
Innovative Polymers specializes in providing technologically advanced polyurethanes for the toughest applications. Our technical support team welcomes the opportunity to partner with our customers in solving processing and performance challenges. If an existing product doesn’t meet project requirements our... » Read More